find_package — CMake 3.30.1 Documentation

# find_package

Note

The `Using Dependencies Guide` provides a high-level introduction to this general topic. It provides a broader overview of where the `find_package()` command fits into the bigger picture, including its relationship to the `FetchContent` module. The guide is recommended pre-reading before moving on to the details below.

Find a package (usually provided by something external to the project), and load its package-specific details. Calls to this command can also be intercepted by dependency providers.

## Typical Usage

Most calls to `find_package()` typically have the following form:

    find_package(<PackageName> [<version>] [REQUIRED] [COMPONENTS <components>...])

The `<PackageName>` is the only mandatory argument. The `<version>` is often omitted, and `REQUIRED` should be given if the project cannot be configured successfully without the package. Some more complicated packages support components which can be selected with the `COMPONENTS` keyword, but most packages don't have that level of complexity.

The above is a reduced form of the basic signature. Where possible, projects should find packages using this form. This reduces complexity and maximizes the ways in which the package can be found or provided.

Understanding the basic signature should be enough for general usage of `find_package()`. Project maintainers who intend to provide a config package should understand the bigger picture, as explained in Full Signature and all subsequent sections on this page.

## Search Modes

The command has a few modes by which it searches for packages:

Module mode

  In this mode, CMake searches for a file called `Find<PackageName>.cmake`, looking first in the locations listed in the `CMAKE_MODULE_PATH`, then among the Find Modules provided by the CMake installation. If the file is found, it is read and processed by CMake. It is responsible for finding the package, checking the version, and producing any needed messages. Some Find modules provide limited or no support for versioning; check the Find module's documentation.

  The `Find<PackageName>.cmake` file is not typically provided by the package itself. Rather, it is normally provided by something external to the package, such as the operating system, CMake itself, or even the project from which the `find_package()` command was called. Being externally provided, Find Modules tend to be heuristic in nature and are susceptible to becoming out-of-date. They typically search for certain libraries, files and other package artifacts.

  Module mode is only supported by the basic command signature.

Config mode

  In this mode, CMake searches for a file called `<lowercasePackageName>-config.cmake` or `<PackageName>Config.cmake`. It will also look for `<lowercasePackageName>-config-version.cmake` or `<PackageName>ConfigVersion.cmake` if version details were specified (see Config Mode Version Selection for an explanation of how these separate version files are used).

  In config mode, the command can be given a list of names to search for as package names. The locations where CMake searches for the config and version files is considerably more complicated than for Module mode (see Config Mode Search Procedure).

  The config and version files are typically installed as part of the package, so they tend to be more reliable than Find modules. They usually contain direct knowledge of the package contents, so no searching or heuristics are needed within the config or version files themselves.

  Config mode is supported by both the basic and full command signatures.

FetchContent redirection mode

  Added in version 3.24: A call to `find_package()` can be redirected internally to a package provided by the `FetchContent` module. To the caller, the behavior will appear similar to Config mode, except that the search logic is by-passed and the component information is not used. See `FetchContent_Declare()` and `FetchContent_MakeAvailable()` for further details.

When not redirected to a package provided by `FetchContent`, the command arguments determine whether Module or Config mode is used. When the basic signature is used, the command searches in Module mode first. If the package is not found, the search falls back to Config mode. A user may set the `CMAKE_FIND_PACKAGE_PREFER_CONFIG` variable to true to reverse the priority and direct CMake to search using Config mode first before falling back to Module mode. The basic signature can also be forced to use only Module mode with a `MODULE` keyword. If the full signature is used, the command only searches in Config mode.

## Basic Signature

    find_package(<PackageName> [version] [EXACT] [QUIET] [MODULE]
                 [REQUIRED] [[COMPONENTS] [components...]]
                 [OPTIONAL_COMPONENTS components...]
                 [REGISTRY_VIEW  (64|32|64_32|32_64|HOST|TARGET|BOTH)]
                 [GLOBAL]
                 [NO_POLICY_SCOPE]
                 [BYPASS_PROVIDER])

The basic signature is supported by both Module and Config modes. The `MODULE` keyword implies that only Module mode can be used to find the package, with no fallback to Config mode.

Regardless of the mode used, a `<PackageName>_FOUND` variable will be set to indicate whether the package was found. When the package is found, package-specific information may be provided through other variables and Imported Targets documented by the package itself. The `QUIET` option disables informational messages, including those indicating that the package cannot be found if it is not `REQUIRED`. The `REQUIRED` option stops processing with an error message if the package cannot be found.

A package-specific list of required components may be listed after the `COMPONENTS` keyword. If any of these components are not able to be satisfied, the package overall is considered to be not found. If the `REQUIRED` option is also present, this is treated as a fatal error, otherwise execution still continues. As a form of shorthand, if the `REQUIRED` option is present, the `COMPONENTS` keyword can be omitted and the required components can be listed directly after `REQUIRED`.

Additional optional components may be listed after `OPTIONAL_COMPONENTS`. If these cannot be satisfied, the package overall can still be considered found, as long as all required components are satisfied.

The set of available components and their meaning are defined by the target package. Formally, it is up to the target package how to interpret the component information given to it, but it should follow the expectations stated above. For calls where no components are specified, there is no single expected behavior and target packages should clearly define what occurs in such cases. Common arrangements include assuming it should find all components, no components or some well-defined subset of the available components.

Added in version 3.24: The `REGISTRY_VIEW` keyword specifies which registry views should be queried. This keyword is only meaningful on `Windows` platforms and will be ignored on all others. Formally, it is up to the target package how to interpret the registry view information given to it.

Added in version 3.24: Specifying the `GLOBAL` keyword will promote all imported targets to a global scope in the importing project. Alternatively, this functionality can be enabled by setting the `CMAKE_FIND_PACKAGE_TARGETS_GLOBAL` variable.

The `[version]` argument requests a version with which the package found should be compatible. There are two possible forms in which it may be specified:

> - A single version with the format `major[.minor[.patch[.tweak]]]`, where each component is a numeric value.

> - A version range with the format `versionMin...[<]versionMax` where `versionMin` and `versionMax` have the same format and constraints on components being integers as the single version. By default, both end points are included. By specifying `<`, the upper end point will be excluded. Version ranges are only supported with CMake 3.19 or later.

The `EXACT` option requests that the version be matched exactly. This option is incompatible with the specification of a version range.

If no `[version]` and/or component list is given to a recursive invocation inside a find-module, the corresponding arguments are forwarded automatically from the outer call (including the `EXACT` flag for `[version]`). Version support is currently provided only on a package-by-package basis (see the Version Selection section below). When a version range is specified but the package is only designed to expect a single version, the package will ignore the upper end point of the range and only take the single version at the lower end of the range into account.

See the `cmake_policy()` command documentation for discussion of the `NO_POLICY_SCOPE` option.

Added in version 3.24: The `BYPASS_PROVIDER` keyword is only allowed when `find_package()` is being called by a dependency provider. It can be used by providers to call the built-in `find_package()` implementation directly and prevent that call from being re-routed back to itself. Future versions of CMake may detect attempts to use this keyword from places other than a dependency provider and halt with a fatal error.

## Full Signature

    find_package(<PackageName> [version] [EXACT] [QUIET]
                 [REQUIRED] [[COMPONENTS] [components...]]
                 [OPTIONAL_COMPONENTS components...]
                 [CONFIG|NO_MODULE]
                 [GLOBAL]
                 [NO_POLICY_SCOPE]
                 [BYPASS_PROVIDER]
                 [NAMES name1 [name2 ...]]
                 [CONFIGS config1 [config2 ...]]
                 [HINTS path1 [path2 ... ]]
                 [PATHS path1 [path2 ... ]]
                 [REGISTRY_VIEW  (64|32|64_32|32_64|HOST|TARGET|BOTH)]
                 [PATH_SUFFIXES suffix1 [suffix2 ...]]
                 [NO_DEFAULT_PATH]
                 [NO_PACKAGE_ROOT_PATH]
                 [NO_CMAKE_PATH]
                 [NO_CMAKE_ENVIRONMENT_PATH]
                 [NO_SYSTEM_ENVIRONMENT_PATH]
                 [NO_CMAKE_PACKAGE_REGISTRY]
                 [NO_CMAKE_BUILDS_PATH] # Deprecated; does nothing.
                 [NO_CMAKE_SYSTEM_PATH]
                 [NO_CMAKE_INSTALL_PREFIX]
                 [NO_CMAKE_SYSTEM_PACKAGE_REGISTRY]
                 [CMAKE_FIND_ROOT_PATH_BOTH |
                  ONLY_CMAKE_FIND_ROOT_PATH |
                  NO_CMAKE_FIND_ROOT_PATH])

The `CONFIG` option, the synonymous `NO_MODULE` option, or the use of options not specified in the basic signature all enforce pure Config mode. In pure Config mode, the command skips Module mode search and proceeds at once with Config mode search.

Config mode search attempts to locate a configuration file provided by the package to be found. A cache entry called `<PackageName>_DIR` is created to hold the directory containing the file. By default, the command searches for a package with the name `<PackageName>`. If the `NAMES` option is given, the names following it are used instead of `<PackageName>`. The names are also considered when determining whether to redirect the call to a package provided by `FetchContent`.

The command searches for a file called `<PackageName>Config.cmake` or `<lowercasePackageName>-config.cmake` for each name specified. A replacement set of possible configuration file names may be given using the `CONFIGS` option. The Config Mode Search Procedure is specified below. Once found, any version constraint is checked, and if satisfied, the configuration file is read and processed by CMake. Since the file is provided by the package it already knows the location of package contents. The full path to the configuration file is stored in the cmake variable `<PackageName>_CONFIG`.

All configuration files which have been considered by CMake while searching for the package with an appropriate version are stored in the `<PackageName>_CONSIDERED_CONFIGS` variable, and the associated versions in the `<PackageName>_CONSIDERED_VERSIONS` variable.

If the package configuration file cannot be found CMake will generate an error describing the problem unless the `QUIET` argument is specified. If `REQUIRED` is specified and the package is not found a fatal error is generated and the configure step stops executing. If `<PackageName>_DIR` has been set to a directory not containing a configuration file CMake will ignore it and search from scratch.

Package maintainers providing CMake package configuration files are encouraged to name and install them such that the Config Mode Search Procedure outlined below will find them without requiring use of additional options.

## Config Mode Search Procedure

Note

When Config mode is used, this search procedure is applied regardless of whether the full or basic signature was given.

Added in version 3.24: All calls to `find_package()` (even in Module mode) first look for a config package file in the `CMAKE_FIND_PACKAGE_REDIRECTS_DIR` directory. The `FetchContent` module, or even the project itself, may write files to that location to redirect `find_package()` calls to content already provided by the project. If no config package file is found in that location, the search proceeds with the logic described below.

CMake constructs a set of possible installation prefixes for the package. Under each prefix several directories are searched for a configuration file. The tables below show the directories searched. Each entry is meant for installation trees following Windows (`W`), UNIX (`U`), or Apple (`A`) conventions:

Entry | Convention
--- | ---
`<prefix>/` | W
`<prefix>/(cmake|CMake)/` | W
`<prefix>/<name>*/` | W
`<prefix>/<name>*/(cmake|CMake)/` | W
`<prefix>/<name>*/(cmake|CMake)/<name>*/` [1] | W
`<prefix>/(lib/<arch>|lib*|share)/cmake/<name>*/` | U
`<prefix>/(lib/<arch>|lib*|share)/<name>*/` | U
`<prefix>/(lib/<arch>|lib*|share)/<name>*/(cmake|CMake)/` | U
`<prefix>/<name>*/(lib/<arch>|lib*|share)/cmake/<name>*/` | W/U
`<prefix>/<name>*/(lib/<arch>|lib*|share)/<name>*/` | W/U
`<prefix>/<name>*/(lib/<arch>|lib*|share)/<name>*/(cmake|CMake)/` | W/U

[1]

Added in version 3.25.

On systems supporting macOS `FRAMEWORK` and `BUNDLE`, the following directories are searched for Frameworks or Application Bundles containing a configuration file:

Entry | Convention
--- | ---
`<prefix>/<name>.framework/Resources/` | A
`<prefix>/<name>.framework/Resources/CMake/` | A
`<prefix>/<name>.framework/Versions/*/Resources/` | A
`<prefix>/<name>.framework/Versions/*/Resources/CMake/` | A
`<prefix>/<name>.app/Contents/Resources/` | A
`<prefix>/<name>.app/Contents/Resources/CMake/` | A

In all cases the `<name>` is treated as case-insensitive and corresponds to any of the names specified (`<PackageName>` or names given by `NAMES`).

If at least one compiled language has been enabled, the architecture-specific `lib/<arch>` and `lib*` directories may be searched based on the compiler's target architecture, in the following order:

`lib/<arch>`

  Searched if the `CMAKE_LIBRARY_ARCHITECTURE` variable is set.

`lib64`

  Searched on 64 bit platforms (`CMAKE_SIZEOF_VOID_P` is 8) and the `FIND_LIBRARY_USE_LIB64_PATHS` property is set to `TRUE`.

`lib32`

  Searched on 32 bit platforms (`CMAKE_SIZEOF_VOID_P` is 4) and the `FIND_LIBRARY_USE_LIB32_PATHS` property is set to `TRUE`.

`libx32`

  Searched on platforms using the x32 ABI if the `FIND_LIBRARY_USE_LIBX32_PATHS` property is set to `TRUE`.

`lib`

  Always searched.

Changed in version 3.24: On `Windows` platform, it is possible to include registry queries as part of the directories specified through `HINTS` and `PATHS` keywords, using a dedicated syntax. Such specifications will be ignored on all other platforms.

Added in version 3.24: `REGISTRY_VIEW` can be specified to manage `Windows` registry queries specified as part of `PATHS` and `HINTS`.

Specify which registry views must be queried. This option is only meaningful on `Windows` platforms and will be ignored on other ones. When not specified, the `TARGET` view is used when the `CMP0134` policy is `NEW`. Refer to `CMP0134` for the default view when the policy is `OLD`.

`64`

  Query the 64-bit registry. On 32-bit Windows, it always returns the string `/REGISTRY-NOTFOUND`.

`32`

  Query the 32-bit registry.

`64_32`

  Query both views (`64` and `32`) and generate a path for each.

`32_64`

  Query both views (`32` and `64`) and generate a path for each.

`HOST`

  Query the registry matching the architecture of the host: `64` on 64-bit Windows and `32` on 32-bit Windows.

`TARGET`

  Query the registry matching the architecture specified by the `CMAKE_SIZEOF_VOID_P` variable. If not defined, fall back to `HOST` view.

`BOTH`

  Query both views (`32` and `64`). The order depends on the following rules: If the `CMAKE_SIZEOF_VOID_P` variable is defined, use the following view depending on the content of this variable:

  - `8`: `64_32`

  - `4`: `32_64`

  If the `CMAKE_SIZEOF_VOID_P` variable is not defined, rely on the architecture of the host:

  - 64-bit: `64_32`

  - 32-bit: `32`

If `PATH_SUFFIXES` is specified, the suffixes are appended to each (`W`) or (`U`) directory entry one-by-one.

This set of directories is intended to work in cooperation with projects that provide configuration files in their installation trees. Directories above marked with (`W`) are intended for installations on Windows where the prefix may point at the top of an application's installation directory. Those marked with (`U`) are intended for installations on UNIX platforms where the prefix is shared by multiple packages. This is merely a convention, so all (`W`) and (`U`) directories are still searched on all platforms. Directories marked with (`A`) are intended for installations on Apple platforms. The `CMAKE_FIND_FRAMEWORK` and `CMAKE_FIND_APPBUNDLE` variables determine the order of preference.

The set of installation prefixes is constructed using the following steps. If `NO_DEFAULT_PATH` is specified all `NO_*` options are enabled.

1. Search prefixes unique to the current `<PackageName>` being found. See policy `CMP0074`.

   Added in version 3.12.

   Specifically, search prefixes specified by the following variables, in order:

   1. `<PackageName>_ROOT` CMake variable, where `<PackageName>` is the case-preserved package name.

   2. `<PACKAGENAME>_ROOT` CMake variable, where `<PACKAGENAME>` is the upper-cased package name. See policy `CMP0144`.

      Added in version 3.27.

   3. `<PackageName>_ROOT` environment variable, where `<PackageName>` is the case-preserved package name.

   4. `<PACKAGENAME>_ROOT` environment variable, where `<PACKAGENAME>` is the upper-cased package name. See policy `CMP0144`.

      Added in version 3.27.

   The package root variables are maintained as a stack so if called from within a find module, root paths from the parent's find module will also be searched after paths for the current package. This can be skipped if `NO_PACKAGE_ROOT_PATH` is passed or by setting the `CMAKE_FIND_USE_PACKAGE_ROOT_PATH` to `FALSE`.

2. Search paths specified in cmake-specific cache variables. These are intended to be used on the command line with a `-DVAR=VALUE`. The values are interpreted as semicolon-separated lists. This can be skipped if `NO_CMAKE_PATH` is passed or by setting the `CMAKE_FIND_USE_CMAKE_PATH` to `FALSE`:

   - `CMAKE_PREFIX_PATH`

   - `CMAKE_FRAMEWORK_PATH`

   - `CMAKE_APPBUNDLE_PATH`

3. Search paths specified in cmake-specific environment variables. These are intended to be set in the user's shell configuration, and therefore use the host's native path separator (`;` on Windows and `:` on UNIX). This can be skipped if `NO_CMAKE_ENVIRONMENT_PATH` is passed or by setting the `CMAKE_FIND_USE_CMAKE_ENVIRONMENT_PATH` to `FALSE`:

   - `<PackageName>_DIR`

   - `CMAKE_PREFIX_PATH`

   - `CMAKE_FRAMEWORK_PATH`

   - `CMAKE_APPBUNDLE_PATH`

4. Search paths specified by the `HINTS` option. These should be paths computed by system introspection, such as a hint provided by the location of another item already found. Hard-coded guesses should be specified with the `PATHS` option.

5. Search the standard system environment variables. This can be skipped if `NO_SYSTEM_ENVIRONMENT_PATH` is passed or by setting the `CMAKE_FIND_USE_SYSTEM_ENVIRONMENT_PATH` to `FALSE`. Path entries ending in `/bin` or `/sbin` are automatically converted to their parent directories:

   - `PATH`

6. Search paths stored in the CMake User Package Registry. This can be skipped if `NO_CMAKE_PACKAGE_REGISTRY` is passed or by setting the variable `CMAKE_FIND_USE_PACKAGE_REGISTRY` to `FALSE` or the deprecated variable `CMAKE_FIND_PACKAGE_NO_PACKAGE_REGISTRY` to `TRUE`.

   See the `cmake-packages(7)` manual for details on the user package registry.

7. Search cmake variables defined in the Platform files for the current system. The searching of `CMAKE_INSTALL_PREFIX` and `CMAKE_STAGING_PREFIX` can be skipped if `NO_CMAKE_INSTALL_PREFIX` is passed or by setting the `CMAKE_FIND_USE_INSTALL_PREFIX` to `FALSE`. All these locations can be skipped if `NO_CMAKE_SYSTEM_PATH` is passed or by setting the `CMAKE_FIND_USE_CMAKE_SYSTEM_PATH` to `FALSE`:

   - `CMAKE_SYSTEM_PREFIX_PATH`

   - `CMAKE_SYSTEM_FRAMEWORK_PATH`

   - `CMAKE_SYSTEM_APPBUNDLE_PATH`

   The platform paths that these variables contain are locations that typically include installed software. An example being `/usr/local` for UNIX based platforms.

8. Search paths stored in the CMake System Package Registry. This can be skipped if `NO_CMAKE_SYSTEM_PACKAGE_REGISTRY` is passed or by setting the `CMAKE_FIND_USE_SYSTEM_PACKAGE_REGISTRY` variable to `FALSE` or the deprecated variable `CMAKE_FIND_PACKAGE_NO_SYSTEM_PACKAGE_REGISTRY` to `TRUE`.

   See the `cmake-packages(7)` manual for details on the system package registry.

9. Search paths specified by the `PATHS` option. These are typically hard-coded guesses.

The `CMAKE_IGNORE_PATH`, `CMAKE_IGNORE_PREFIX_PATH`, `CMAKE_SYSTEM_IGNORE_PATH` and `CMAKE_SYSTEM_IGNORE_PREFIX_PATH` variables can also cause some of the above locations to be ignored.

Added in version 3.16: Added the `CMAKE_FIND_USE_<CATEGORY>` variables to globally disable various search locations.

The CMake variable `CMAKE_FIND_ROOT_PATH` specifies one or more directories to be prepended to all other search directories. This effectively "re-roots" the entire search under given locations. Paths which are descendants of the `CMAKE_STAGING_PREFIX` are excluded from this re-rooting, because that variable is always a path on the host system. By default the `CMAKE_FIND_ROOT_PATH` is empty.

The `CMAKE_SYSROOT` variable can also be used to specify exactly one directory to use as a prefix. Setting `CMAKE_SYSROOT` also has other effects. See the documentation for that variable for more.

These variables are especially useful when cross-compiling to point to the root directory of the target environment and CMake will search there too. By default at first the directories listed in `CMAKE_FIND_ROOT_PATH` are searched, then the `CMAKE_SYSROOT` directory is searched, and then the non-rooted directories will be searched. The default behavior can be adjusted by setting `CMAKE_FIND_ROOT_PATH_MODE_PACKAGE`. This behavior can be manually overridden on a per-call basis using options:

`CMAKE_FIND_ROOT_PATH_BOTH`

  Search in the order described above.

`NO_CMAKE_FIND_ROOT_PATH`

  Do not use the `CMAKE_FIND_ROOT_PATH` variable.

`ONLY_CMAKE_FIND_ROOT_PATH`

  Search only the re-rooted directories and directories below `CMAKE_STAGING_PREFIX`.

The default search order is designed to be most-specific to least-specific for common use cases. Projects may override the order by simply calling the command multiple times and using the `NO_*` options:

    find_package (<PackageName> PATHS paths... NO_DEFAULT_PATH)
    find_package (<PackageName>)

Once one of the calls succeeds the result variable will be set and stored in the cache so that no call will search again.

By default the value stored in the result variable will be the path at which the file is found. The `CMAKE_FIND_PACKAGE_RESOLVE_SYMLINKS` variable may be set to `TRUE` before calling `find_package` in order to resolve symbolic links and store the real path to the file.

Every non-REQUIRED `find_package` call can be disabled or made REQUIRED:

- Setting the `CMAKE_DISABLE_FIND_PACKAGE_<PackageName>` variable to `TRUE` disables the package. This also disables redirection to a package provided by `FetchContent`.

- Setting the `CMAKE_REQUIRE_FIND_PACKAGE_<PackageName>` variable to `TRUE` makes the package REQUIRED.

Setting both variables to `TRUE` simultaneously is an error.

## Config Mode Version Selection

Note

When Config mode is used, this version selection process is applied regardless of whether the full or basic signature was given.

When the `[version]` argument is given, Config mode will only find a version of the package that claims compatibility with the requested version (see format specification). If the `EXACT` option is given, only a version of the package claiming an exact match of the requested version may be found. CMake does not establish any convention for the meaning of version numbers. Package version numbers are checked by "version" files provided by the packages themselves or by `FetchContent`. For a candidate package configuration file `<config-file>.cmake` the corresponding version file is located next to it and named either `<config-file>-version.cmake` or `<config-file>Version.cmake`. If no such version file is available then the configuration file is assumed to not be compatible with any requested version. A basic version file containing generic version matching code can be created using the `CMakePackageConfigHelpers` module. When a version file is found it is loaded to check the requested version number. The version file is loaded in a nested scope in which the following variables have been defined:

`PACKAGE_FIND_NAME`

  The `<PackageName>`

`PACKAGE_FIND_VERSION`

  Full requested version string

`PACKAGE_FIND_VERSION_MAJOR`

  Major version if requested, else 0

`PACKAGE_FIND_VERSION_MINOR`

  Minor version if requested, else 0

`PACKAGE_FIND_VERSION_PATCH`

  Patch version if requested, else 0

`PACKAGE_FIND_VERSION_TWEAK`

  Tweak version if requested, else 0

`PACKAGE_FIND_VERSION_COUNT`

  Number of version components, 0 to 4

When a version range is specified, the above version variables will hold values based on the lower end of the version range. This is to preserve compatibility with packages that have not been implemented to expect version ranges. In addition, the version range will be described by the following variables:

`PACKAGE_FIND_VERSION_RANGE`

  Full requested version range string

`PACKAGE_FIND_VERSION_RANGE_MIN`

  This specifies whether the lower end point of the version range should be included or excluded. Currently, the only supported value for this variable is `INCLUDE`.

`PACKAGE_FIND_VERSION_RANGE_MAX`

  This specifies whether the upper end point of the version range should be included or excluded. The supported values for this variable are `INCLUDE` and `EXCLUDE`.

`PACKAGE_FIND_VERSION_MIN`

  Full requested version string of the lower end point of the range

`PACKAGE_FIND_VERSION_MIN_MAJOR`

  Major version of the lower end point if requested, else 0

`PACKAGE_FIND_VERSION_MIN_MINOR`

  Minor version of the lower end point if requested, else 0

`PACKAGE_FIND_VERSION_MIN_PATCH`

  Patch version of the lower end point if requested, else 0

`PACKAGE_FIND_VERSION_MIN_TWEAK`

  Tweak version of the lower end point if requested, else 0

`PACKAGE_FIND_VERSION_MIN_COUNT`

  Number of version components of the lower end point, 0 to 4

`PACKAGE_FIND_VERSION_MAX`

  Full requested version string of the upper end point of the range

`PACKAGE_FIND_VERSION_MAX_MAJOR`

  Major version of the upper end point if requested, else 0

`PACKAGE_FIND_VERSION_MAX_MINOR`

  Minor version of the upper end point if requested, else 0

`PACKAGE_FIND_VERSION_MAX_PATCH`

  Patch version of the upper end point if requested, else 0

`PACKAGE_FIND_VERSION_MAX_TWEAK`

  Tweak version of the upper end point if requested, else 0

`PACKAGE_FIND_VERSION_MAX_COUNT`

  Number of version components of the upper end point, 0 to 4

Regardless of whether a single version or a version range is specified, the variable `PACKAGE_FIND_VERSION_COMPLETE` will be defined and will hold the full requested version string as specified.

The version file checks whether it satisfies the requested version and sets these variables:

`PACKAGE_VERSION`

  Full provided version string

`PACKAGE_VERSION_EXACT`

  True if version is exact match

`PACKAGE_VERSION_COMPATIBLE`

  True if version is compatible

`PACKAGE_VERSION_UNSUITABLE`

  True if unsuitable as any version

These variables are checked by the `find_package` command to determine whether the configuration file provides an acceptable version. They are not available after the `find_package` call returns. If the version is acceptable the following variables are set:

`<PackageName>_VERSION`

  Full provided version string

`<PackageName>_VERSION_MAJOR`

  Major version if provided, else 0

`<PackageName>_VERSION_MINOR`

  Minor version if provided, else 0

`<PackageName>_VERSION_PATCH`

  Patch version if provided, else 0

`<PackageName>_VERSION_TWEAK`

  Tweak version if provided, else 0

`<PackageName>_VERSION_COUNT`

  Number of version components, 0 to 4

and the corresponding package configuration file is loaded. When multiple package configuration files are available whose version files claim compatibility with the version requested it is unspecified which one is chosen: unless the variable `CMAKE_FIND_PACKAGE_SORT_ORDER` is set no attempt is made to choose a highest or closest version number.

To control the order in which `find_package` checks for compatibility use the two variables `CMAKE_FIND_PACKAGE_SORT_ORDER` and `CMAKE_FIND_PACKAGE_SORT_DIRECTION`. For instance in order to select the highest version one can set

    SET(CMAKE_FIND_PACKAGE_SORT_ORDER NATURAL)
    SET(CMAKE_FIND_PACKAGE_SORT_DIRECTION DEC)

before calling `find_package`.

## Package File Interface Variables

When loading a find module or package configuration file `find_package` defines variables to provide information about the call arguments (and restores their original state before returning):

`CMAKE_FIND_PACKAGE_NAME`

  The `<PackageName>` which is searched for

`<PackageName>_FIND_REQUIRED`

  True if `REQUIRED` option was given

`<PackageName>_FIND_QUIETLY`

  True if `QUIET` option was given

`<PackageName>_FIND_REGISTRY_VIEW`

  The requested view if `REGISTRY_VIEW` option was given

`<PackageName>_FIND_VERSION`

  Full requested version string

`<PackageName>_FIND_VERSION_MAJOR`

  Major version if requested, else 0

`<PackageName>_FIND_VERSION_MINOR`

  Minor version if requested, else 0

`<PackageName>_FIND_VERSION_PATCH`

  Patch version if requested, else 0

`<PackageName>_FIND_VERSION_TWEAK`

  Tweak version if requested, else 0

`<PackageName>_FIND_VERSION_COUNT`

  Number of version components, 0 to 4

`<PackageName>_FIND_VERSION_EXACT`

  True if `EXACT` option was given

`<PackageName>_FIND_COMPONENTS`

  List of specified components (required and optional)

`<PackageName>_FIND_REQUIRED_<c>`

  True if component `<c>` is required, false if component `<c>` is optional

When a version range is specified, the above version variables will hold values based on the lower end of the version range. This is to preserve compatibility with packages that have not been implemented to expect version ranges. In addition, the version range will be described by the following variables:

`<PackageName>_FIND_VERSION_RANGE`

  Full requested version range string

`<PackageName>_FIND_VERSION_RANGE_MIN`

  This specifies whether the lower end point of the version range is included or excluded. Currently, `INCLUDE` is the only supported value.

`<PackageName>_FIND_VERSION_RANGE_MAX`

  This specifies whether the upper end point of the version range is included or excluded. The possible values for this variable are `INCLUDE` or `EXCLUDE`.

`<PackageName>_FIND_VERSION_MIN`

  Full requested version string of the lower end point of the range

`<PackageName>_FIND_VERSION_MIN_MAJOR`

  Major version of the lower end point if requested, else 0

`<PackageName>_FIND_VERSION_MIN_MINOR`

  Minor version of the lower end point if requested, else 0

`<PackageName>_FIND_VERSION_MIN_PATCH`

  Patch version of the lower end point if requested, else 0

`<PackageName>_FIND_VERSION_MIN_TWEAK`

  Tweak version of the lower end point if requested, else 0

`<PackageName>_FIND_VERSION_MIN_COUNT`

  Number of version components of the lower end point, 0 to 4

`<PackageName>_FIND_VERSION_MAX`

  Full requested version string of the upper end point of the range

`<PackageName>_FIND_VERSION_MAX_MAJOR`

  Major version of the upper end point if requested, else 0

`<PackageName>_FIND_VERSION_MAX_MINOR`

  Minor version of the upper end point if requested, else 0

`<PackageName>_FIND_VERSION_MAX_PATCH`

  Patch version of the upper end point if requested, else 0

`<PackageName>_FIND_VERSION_MAX_TWEAK`

  Tweak version of the upper end point if requested, else 0

`<PackageName>_FIND_VERSION_MAX_COUNT`

  Number of version components of the upper end point, 0 to 4

Regardless of whether a single version or a version range is specified, the variable `<PackageName>_FIND_VERSION_COMPLETE` will be defined and will hold the full requested version string as specified.

In Module mode the loaded find module is responsible to honor the request detailed by these variables; see the find module for details. In Config mode `find_package` handles `REQUIRED`, `QUIET`, and `[version]` options automatically but leaves it to the package configuration file to handle components in a way that makes sense for the package. The package configuration file may set `<PackageName>_FOUND` to false to tell `find_package` that component requirements are not satisfied.