Installation Instructions
S3 86C801/805/805i/928/928PCI OS/2 Beta Drivers

Date:	11/30/93

Installation Considerations

1.	The installation process assumes that the user knows the  
	maximum vertical refresh rate as well as the maximum 
	resolution of the monitor.

2.	When installing the S3 driver over a non-S3 driver 
	(e.g., SVGA), the standard IBM VGA driver must be 
	installed first.  This is not required if an S3 driver is 
	already installed.

3.	The driver diskette must be labeled "S3 DRVS".  If it is 
	not labeled installation will fail.

4.	The S3 driver will not install unless an S3 chip-based 
	card is installed in the machine at the time of driver 
	installation. 
  
5.	This driver is for the S3 86C80X/928 chips with an AT&T
	491-compatible RAMDAC and the 86C928 with a Brooktree 
	BT485 RAMDAC.

6.	The 86C928 with Brooktree Bt485 RAMDAC does not support 
	the 1280x1024x256 color resolution.

7.	S3 cards with GENDAC I or II are not supported. 


Installation Instructions


1.	Open an OS/2 command prompt (windowed or full screen).

2.	Insert driver diskette into the floppy drive. 

3.	Change to the floppy drive (A: or B:) into which you have 
	inserted the driver diskette.  Verify that the diskette 
	is labeled "S3 DRVS".  If it is not labeled then type 
	"label S3 DRVS".

4.	Type S3INST A: C: and press "Enter".  ("A" is the floppy 
	drive; "C" is the drive OS/2 2.1 is installed).

5.    	When prompted, exit the OS/2 command prompt, remove floppy
 	disk from drive, and shutdown and reboot system.

6.	Make sure you have all open data files saved before 
	continuing the S3 driver installation.
 
7.	Make sure Win-OS/2 session and all Seamless Windows 
	applications are closed. (Seamless applications are 
	windows applications that run on top of the PM Desktop.)

8.	Double click on the the "OS/2 System" icon.

9.	Double click on the "System Setup" icon.

10.  	Double click on the "Display Driver Install" icon. 

11.	When prompted by the Display Driver Install dialog, select
	Primary Display and then click the OK button.

12.	Select the "32 Bit S3 Display Drivers" option from the 
	Primary Display Adapter Type dialog and click the OK 
	button.

13.	Select the appropriate option from the Monitor 
	Configuration/Selection Utility dialog, and click the 
	OK button.

	THE SCREEN WILL TEMPORARILY FLASH AND GO BLACK.  PLEASE
	WAIT FOR THE SOURCE DIRECTORY DIALOG TO APPEAR.

14.	Insert driver diskette into the floppy drive.

15.	The Source Directory dialog will be displayed.  Make sure 
	the source directory is set to the location from which you
	are installing and select Install.

16.	The Installation Program may pause and display prompts to 
	overwrite certain files. Please answer YES for each file.


17.	You will be given a message stating that you "Must 
	Shutdown and Restart your system for the changes to take 
	effect".  Click the OK button.

18.	Remove driver diskette from the floppy drive.

19.	Shut down and reboot system.  

	After you reboot your system will come up with your newly 
	installed driver.


To Change Resolutions:

20.	To switch resolutions, double click on the "System" icon  
	in the System Setup Folder.

21. 	Highlight the resolution and close the dialog.

22.	Shut down and reboot.


To restore to VGA follow the instructions in the "README.IBM" file.


