Common YANG Data Types

<CODE BEGINS> file "ietf-yang-types@2025-06-23.yang"
module ietf-yang-types {

  namespace "urn:ietf:params:xml:ns:yang:ietf-yang-types";
  prefix "yang";

  organization
   "IETF Network Modeling (NETMOD) Working Group";

  contact
   "WG Web:   <https://datatracker.ietf.org/wg/netmod/>
    WG List:  <mailto:netmod@ietf.org>

    Editor:   Juergen Schoenwaelder
              <mailto:jschoenwaelder@constructor.university>";

  description
   "This module contains a collection of generally useful derived
    YANG data types.

    The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
    NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
    'MAY', and 'OPTIONAL' in this document are to be interpreted as
    described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
    they appear in all capitals, as shown here.

    Copyright (c) 2025 IETF Trust and the persons identified as
    authors of the code.  All rights reserved.

    Redistribution and use in source and binary forms, with or
    without modification, is permitted pursuant to, and subject
    to the license terms contained in, the Revised BSD License
    set forth in Section 4.c of the IETF Trust's Legal Provisions
    Relating to IETF Documents
    (https://trustee.ietf.org/license-info).

    This version of this YANG module is part of RFC XXXX;
    see the RFC itself for full legal notices.";

  revision 2025-06-23 {
    description
     "This revision adds the following new data types:
      - yang:date
      - yang:date-no-zone
      - yang:time
      - yang:time-no-zone
      - yang:hours32
      - yang:minutes32
      - yang:seconds32
      - yang:centiseconds32
      - yang:milliseconds32
      - yang:microseconds32
      - yang:microseconds64
      - yang:nanoseconds32
      - yang:nanoseconds64
      - yang:language-tag
      The yang-identifier definition has been aligned with YANG
      1.1 and types representing time support the representation
      of leap seconds. The representation of time zone offsets
      has been aligned with RFC 9557. Several description and
      pattern statements have been improved.";
    reference
     "RFC XXXX: Common YANG Data Types";
  }

  revision 2013-07-15 {
    description
     "This revision adds the following new data types:
      - yang:yang-identifier
      - yang:hex-string
      - yang:uuid
      - yang:dotted-quad";
    reference
     "RFC 6991: Common YANG Data Types";
  }

  revision 2010-09-24 {
    description
     "Initial revision.";
    reference
     "RFC 6021: Common YANG Data Types";
  }

  /*** collection of counter and gauge types ***/

  typedef counter32 {
    type uint32;
    description
     "The counter32 type represents a non-negative integer
      that monotonically increases until it reaches a
      maximum value of 2^32-1 (4294967295 decimal), when it
      wraps around and starts increasing again from zero.

      Counters have no defined 'initial' value, and thus, a
      single value of a counter has (in general) no information
      content.  Discontinuities in the monotonically increasing
      value normally occur at re-initialization of the
      management system, and at other times as specified in the
      description of a schema node using this type.  If such
      other times can occur, for example, the instantiation of
      a schema node of type counter32 at times other than
      re-initialization, then a corresponding schema node
      should be defined, with an appropriate type, to indicate
      the last discontinuity.

      The counter32 type should not be used for configuration
      schema nodes.  A default statement SHOULD NOT be used in
      combination with the type counter32.

      In the value set and its semantics, this type is equivalent
      to the Counter32 type of the SMIv2.";
    reference
     "RFC 2578: Structure of Management Information Version 2
                (SMIv2)";
  }

  typedef zero-based-counter32 {
    type counter32;
    default "0";
    description
     "The zero-based-counter32 type represents a counter32
      that has the defined 'initial' value zero.

      A data tree node using this type will be set to zero (0)
      on creation and will thereafter increase monotonically until
      it reaches a maximum value of 2^32-1 (4294967295 decimal),
      when it wraps around and starts increasing again from zero.

      Provided that an application discovers a new data tree node
      using this type within the minimum time to wrap, it can use
      the 'initial' value as a delta.  It is important for a
      management station to be aware of this minimum time and the
      actual time between polls, and to discard data if the actual
      time is too long or there is no defined minimum time.

      In the value set and its semantics, this type is equivalent
      to the ZeroBasedCounter32 textual convention of the SMIv2.";
    reference
      "RFC 4502: Remote Network Monitoring Management Information
                 Base Version 2";
  }

  typedef counter64 {
    type uint64;
    description
     "The counter64 type represents a non-negative integer
      that monotonically increases until it reaches a
      maximum value of 2^64-1 (18446744073709551615 decimal),
      when it wraps around and starts increasing again from zero.

      Counters have no defined 'initial' value, and thus, a
      single value of a counter has (in general) no information
      content.  Discontinuities in the monotonically increasing
      value normally occur at re-initialization of the
      management system, and at other times as specified in the
      description of a schema node using this type.  If such
      other times can occur, for example, the instantiation of
      a schema node of type counter64 at times other than
      re-initialization, then a corresponding schema node
      should be defined, with an appropriate type, to indicate
      the last discontinuity.

      The counter64 type should not be used for configuration
      schema nodes.  A default statement SHOULD NOT be used in
      combination with the type counter64.

      In the value set and its semantics, this type is equivalent
      to the Counter64 type of the SMIv2.";
    reference
     "RFC 2578: Structure of Management Information Version 2
                (SMIv2)";
  }

  typedef zero-based-counter64 {
    type counter64;
    default "0";
    description
     "The zero-based-counter64 type represents a counter64 that
      has the defined 'initial' value zero.

      A data tree node using this type will be set to zero (0)
      on creation and will thereafter increase monotonically until
      it reaches a maximum value of 2^64-1 (18446744073709551615
      decimal), when it wraps around and starts increasing again
      from zero.

      Provided that an application discovers a new data tree node
      using this type within the minimum time to wrap, it can use
      the 'initial' value as a delta.  It is important for a
      management station to be aware of this minimum time and the
      actual time between polls, and to discard data if the actual
      time is too long or there is no defined minimum time.

      In the value set and its semantics, this type is equivalent
      to the ZeroBasedCounter64 textual convention of the SMIv2.";
    reference
     "RFC 2856: Textual Conventions for Additional High Capacity
                Data Types";
  }

  typedef gauge32 {
    type uint32;
    description
     "The gauge32 type represents a non-negative integer, which
      may increase or decrease, but shall never exceed a maximum
      value, nor fall below a minimum value.  The maximum value
      cannot be greater than 2^32-1 (4294967295 decimal), and
      the minimum value cannot be smaller than 0.  The value of
      a gauge32 has its maximum value whenever the information
      being modeled is greater than or equal to its maximum
      value, and has its minimum value whenever the information
      being modeled is smaller than or equal to its minimum value.
      If the information being modeled subsequently decreases
      below (increases above) the maximum (minimum) value, the
      gauge32 also decreases (increases).

      In the value set and its semantics, this type is equivalent
      to the Gauge32 type of the SMIv2.";
    reference
     "RFC 2578: Structure of Management Information Version 2
                (SMIv2)";
  }

  typedef gauge64 {
    type uint64;
    description
     "The gauge64 type represents a non-negative integer, which
      may increase or decrease, but shall never exceed a maximum
      value, nor fall below a minimum value.  The maximum value
      cannot be greater than 2^64-1 (18446744073709551615), and
      the minimum value cannot be smaller than 0.  The value of
      a gauge64 has its maximum value whenever the information
      being modeled is greater than or equal to its maximum
      value, and has its minimum value whenever the information
      being modeled is smaller than or equal to its minimum value.
      If the information being modeled subsequently decreases
      below (increases above) the maximum (minimum) value, the
      gauge64 also decreases (increases).

      In the value set and its semantics, this type is equivalent
      to the CounterBasedGauge64 SMIv2 textual convention defined
      in RFC 2856";
    reference
     "RFC 2856: Textual Conventions for Additional High Capacity
                Data Types";
  }

  /*** collection of identifier-related types ***/

  typedef object-identifier {
    type string {
      pattern '(([0-1](\.[1-3]?[0-9]))|(2\.(0|([1-9][0-9]*))))'
            + '(\.(0|([1-9][0-9]*)))*';
    }
    description
     "The object-identifier type represents administratively
      assigned names in a registration-hierarchical-name tree.

      Values of this type are denoted as a sequence of numerical
      non-negative sub-identifier values.  Each sub-identifier
      value MUST NOT exceed 2^32-1 (4294967295).  Sub-identifiers
      are separated by single dots and without any intermediate
      whitespace.

      The ASN.1 standard restricts the value space of the first
      sub-identifier to 0, 1, or 2.  Furthermore, the value space
      of the second sub-identifier is restricted to the range
      0 to 39 if the first sub-identifier is 0 or 1.  Finally,
      the ASN.1 standard requires that an object identifier
      has always at least two sub-identifiers.  The pattern
      captures these restrictions.

      Although the number of sub-identifiers is not limited,
      module designers should realize that there may be
      implementations that stick with the SMIv2 limit of 128
      sub-identifiers.

      This type is a superset of the SMIv2 OBJECT IDENTIFIER type
      since it is not restricted to 128 sub-identifiers.  Hence,
      this type SHOULD NOT be used to represent the SMIv2 OBJECT
      IDENTIFIER type; the object-identifier-128 type SHOULD be
      used instead.";
    reference
     "ISO9834-1: Information technology -- Open Systems
      Interconnection -- Procedures for the operation of OSI
      Registration Authorities: General procedures and top
      arcs of the ASN.1 Object Identifier tree";
  }

  typedef object-identifier-128 {
    type object-identifier {
      pattern '[0-9]*(\.[0-9]*){1,127}';
    }
    description
     "This type represents object-identifiers restricted to 128
      sub-identifiers.

      In the value set and its semantics, this type is equivalent
      to the OBJECT IDENTIFIER type of the SMIv2.";
    reference
     "RFC 2578: Structure of Management Information Version 2
                (SMIv2)";
  }

  /*** collection of types related to date and time ***/

  typedef date-and-time {
    type string {
      pattern
          '[0-9]{4}-(1[0-2]|0[1-9])-(0[1-9]|[1-2][0-9]|3[0-1])'
        + 'T(0[0-9]|1[0-9]|2[0-3]):[0-5][0-9]:([0-5][0-9]|60)(\.[0-9]+)?'
        + '(Z|[\+\-]((1[0-3]|0[0-9]):([0-5][0-9])|14:00))?';
    }
    description
     "The date-and-time type is a profile of the ISO 8601
      standard for representation of dates and times using the
      Gregorian calendar.  The profile is defined by the
      date-time production in Section 5.6 of RFC 3339 and the
      update defined in Section 2 of RFC 9557 . The value of
      60 for seconds is allowed only in the case of leap seconds.

      The date-and-time type is compatible with the dateTime XML
      schema dateTime type with the following notable exceptions:

      (a) The date-and-time type does not allow negative years.

      (b) The time-offset Z indicates that the date-and-time
          value is reported in UTC and that the local time zone
          reference point is unknown. The time-offsets +00:00
          indicates that the date-and-time value is reported in
          UTC and that the local time reference point is UTC
          (see RFC 9557 section 2).

      This type is not equivalent to the DateAndTime textual
      convention of the SMIv2 since RFC 3339 uses a different
      separator between full-date and full-time and provides
      higher resolution of time-secfrac.

      The canonical format for date-and-time values with a known time
      zone uses a numeric time zone offset that is calculated using
      the device's configured known offset to UTC time.  A change of
      the device's offset to UTC time will cause date-and-time values
      to change accordingly.  Such changes might happen periodically
      in case a server follows automatically daylight saving time
      (DST) time zone offset changes.  The canonical format for
      date-and-time values reported in UTC with an unknown local
      time zone offset SHOULD use the time-offset Z and MAY use
      -00:00 for backwards compatibility.";
    reference
     "RFC 3339: Date and Time on the Internet: Timestamps
      RFC 9557: Date and Time on the Internet: Timestamps
                with Additional Information
      RFC 2579: Textual Conventions for SMIv2
      XSD-TYPES: XML Schema Definition Language (XSD) 1.1
                 Part 2: Datatypes";
  }

  typedef date {
    type string {
      pattern
          '[0-9]{4}-(1[0-2]|0[1-9])-(0[1-9]|[1-2][0-9]|3[0-1])'
        + '(Z|[\+\-]((1[0-3]|0[0-9]):([0-5][0-9])|14:00))?';
    }
    description
     "The date type represents a time-interval of the length
      of a day, i.e., 24 hours. It includes an optional time
      zone offset.

      The date type is compatible with the XML schema date
      type with the following notable exceptions:

      (a) The date type does not allow negative years.

      (b) The time-offset Z indicates that the date value is
          reported in UTC and that the local time zone reference
          point is unknown. The time-offset +00:00 indicates that
          the date value is reported in UTC and that the local
          time reference point is UTC (see RFC 9557 section 2).

      The canonical format for date values with a known time
      zone uses a numeric time zone offset that is calculated using
      the device's configured known offset to UTC time.  A change of
      the device's offset to UTC time will cause date values
      to change accordingly.  Such changes might happen periodically
      in case a server follows automatically daylight saving time
      (DST) time zone offset changes.  The canonical format for
      date values reported in UTC with an unknown local time zone
      offset uses the time-offset Z.";
    reference
     "RFC 3339: Date and Time on the Internet: Timestamps
      RFC 9557: Date and Time on the Internet: Timestamps
                with Additional Information
      XSD-TYPES: XML Schema Definition Language (XSD) 1.1
                 Part 2: Datatypes";
  }

  typedef date-no-zone {
    type date {
      pattern '[0-9]{4}-(1[0-2]|0[1-9])-(0[1-9]|[1-2][0-9]|3[0-1])';
    }
    description
     "The date-no-zone type represents a date without the optional
      time zone offset information.";
  }

  typedef time {
    type string {
      pattern
          '(0[0-9]|1[0-9]|2[0-3]):[0-5][0-9]:([0-5][0-9]|60)(\.[0-9]+)?'
        + '(Z|[\+\-]((1[0-3]|0[0-9]):([0-5][0-9])|14:00))?';
    }
    description
     "The time type represents an instance of time of zero-duration
      that recurs every day. It includes an optional time zone
      offset. The value of 60 for seconds is allowed only in the
      case of leap seconds.

      The time type is compatible with the XML schema time
      type with the following notable exception:

      (a) The time-offset Z indicates that the time value is
          reported in UTC and that the local time zone reference
          point is unknown. The time-offset +00:00 indicates that
          the time value is reported in UTC and that the local
          time reference point is UTC (see RFC 9557 section 2).

      The canonical format for time values with a known time
      zone uses a numeric time zone offset that is calculated using
      the device's configured known offset to UTC time.  A change of
      the device's offset to UTC time will cause time values
      to change accordingly.  Such changes might happen periodically
      in case a server follows automatically daylight saving time
      (DST) time zone offset changes.  The canonical format for
      time values reported in UTC with an unknown local time zone
      offset uses the time-offset Z.";
    reference
     "RFC 3339: Date and Time on the Internet: Timestamps
      RFC 9557: Date and Time on the Internet: Timestamps
                with Additional Information
      XSD-TYPES: XML Schema Definition Language (XSD) 1.1
                 Part 2: Datatypes";
  }

  typedef time-no-zone {
    type time {
      pattern
          '(0[0-9]|1[0-9]|2[0-3]):[0-5][0-9]:([0-5][0-9]|60)(\.[0-9]+)?';
    }
    description
     "The time-no-zone type represents a time without the optional
      time zone offset information.";
  }

  typedef hours32 {
    type int32;
    units "hours";
    description
     "A period of time, measured in units of hours.

      The maximum time period that can be expressed is in the
      range [-89478485 days 08:00:00 to 89478485 days 07:00:00].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef minutes32 {
    type int32;
    units "minutes";
    description
     "A period of time, measured in units of minutes.

      The maximum time period that can be expressed is in the
      range [-1491308 days 2:08:00 to 1491308 days 2:07:00].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef seconds32 {
    type int32;
    units "seconds";
    description
     "A period of time, measured in units of seconds.

      The maximum time period that can be expressed is in the
      range [-24855 days 03:14:08 to 24855 days 03:14:07].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef centiseconds32 {
    type int32;
    units "centiseconds";
    description
     "A period of time, measured in units of 10^-2 seconds.

      The maximum time period that can be expressed is in the
      range [-248 days 13:13:56 to 248 days 13:13:56].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef milliseconds32 {
    type int32;
    units "milliseconds";
    description
     "A period of time, measured in units of 10^-3 seconds.

      The maximum time period that can be expressed is in the
      range [-24 days 20:31:23 to 24 days 20:31:23].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef microseconds32 {
    type int32;
    units "microseconds";
    description
     "A period of time, measured in units of 10^-6 seconds.

      The maximum time period that can be expressed is in the
      range [-00:35:47 to 00:35:47].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef microseconds64 {
    type int64;
    units "microseconds";
    description
     "A period of time, measured in units of 10^-6 seconds.

      The maximum time period that can be expressed is in the
      range [-106751991 days 04:00:54 to 106751991 days 04:00:54].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef nanoseconds32 {
    type int32;
    units "nanoseconds";
    description
     "A period of time, measured in units of 10^-9 seconds.

      The maximum time period that can be expressed is in the
      range [-00:00:02 to 00:00:02].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef nanoseconds64 {
    type int64;
    units "nanoseconds";
    description
     "A period of time, measured in units of 10^-9 seconds.

      The maximum time period that can be expressed is in the
      range [-106753 days 23:12:44 to 106752 days 0:47:16].

      This type should be range restricted in situations
      where only non-negative time periods are desirable,
      (i.e., range '0..max').";
  }

  typedef timeticks {
    type uint32;
    description
     "The timeticks type represents a non-negative integer that
      represents the time, modulo 2^32 (4294967296 decimal), in
      hundredths of a second between two epochs.  When a schema
      node is defined that uses this type, the description of
      the schema node identifies both of the reference epochs.

      In the value set and its semantics, this type is equivalent
      to the TimeTicks type of the SMIv2.";
    reference
     "RFC 2578: Structure of Management Information Version 2
                (SMIv2)";
  }

  typedef timestamp {
    type timeticks;
    description
     "The timestamp type represents the value of an associated
      timeticks schema node instance at which a specific occurrence
      happened.  The specific occurrence must be defined in the
      description of any schema node defined using this type.  When
      the specific occurrence occurred prior to the last time the
      associated timeticks schema node instance was zero, then the
      timestamp value is zero.

      Note that this requires all timestamp values to be reset to
      zero when the value of the associated timeticks schema node
      instance reaches 497+ days and wraps around to zero.

      The associated timeticks schema node must be specified
      in the description of any schema node using this type.

      In the value set and its semantics, this type is equivalent
      to the TimeStamp textual convention of the SMIv2.";
    reference
     "RFC 2579: Textual Conventions for SMIv2";
  }

  /*** collection of generic address types ***/

  typedef phys-address {
    type string {
      pattern '([0-9a-fA-F]{2}(:[0-9a-fA-F]{2})*)?';
    }
    description
     "Represents media- or physical-level addresses represented
      as a sequence octets, each octet represented by two hexadecimal
      numbers.  Octets are separated by colons.  The canonical
      representation uses lowercase characters.

      In the value set and its semantics, this type is equivalent
      to the PhysAddress textual convention of the SMIv2.";
    reference
     "RFC 2579: Textual Conventions for SMIv2";
  }

  typedef mac-address {
    type string {
      pattern '[0-9a-fA-F]{2}(:[0-9a-fA-F]{2}){5}';
    }
    description
     "The mac-address type represents a 48-bit IEEE 802 MAC
      address. The canonical representation uses lowercase
      characters. Note that there are IEEE 802 MAC addresses
      with a different length that this type cannot represent.
      The phys-address type may be used to represent physical
      addresses of varying length.

      In the value set and its semantics, this type is equivalent
      to the MacAddress textual convention of the SMIv2.";
    reference
     "IEEE 802: IEEE Standard for Local and Metropolitan Area
                Networks: Overview and Architecture
      RFC 2579: Textual Conventions for SMIv2";
  }

  /*** collection of XML-specific types ***/

  typedef xpath1.0 {
    type string;
    description
     "This type represents an XPATH 1.0 expression.

      When a schema node is defined that uses this type, the
      description of the schema node MUST specify the XPath
      context in which the XPath expression is evaluated.";
    reference
     "XPATH: XML Path Language (XPath) Version 1.0";
  }

  /*** collection of string types ***/

  typedef hex-string {
    type string {
      pattern '([0-9a-fA-F]{2}(:[0-9a-fA-F]{2})*)?';
    }
    description
     "A hexadecimal string with octets represented as hex digits
      separated by colons.  The canonical representation uses
      lowercase characters.";
  }

  typedef uuid {
    type string {
      pattern '[0-9a-fA-F]{8}-[0-9a-fA-F]{4}-[0-9a-fA-F]{4}-'
            + '[0-9a-fA-F]{4}-[0-9a-fA-F]{12}';
    }
    description
     "A Universally Unique IDentifier in the string representation
      defined in RFC 4122.  The canonical representation uses
      lowercase characters.

      The following is an example of a UUID in string representation:
      f81d4fae-7dec-11d0-a765-00a0c91e6bf6
      ";
    reference
     "RFC 4122: A Universally Unique IDentifier (UUID) URN
                Namespace";
  }

  typedef dotted-quad {
    type string {
      pattern
        '(([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])\.){3}'
      + '([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])';
    }
    description
      "An unsigned 32-bit number expressed in the dotted-quad
       notation, i.e., four octets written as decimal numbers
       and separated with the '.' (full stop) character.";
  }

  typedef language-tag {
    type string;
    description
       "A language tag according to RFC 5646 (BCP 47). The
        canonical representation uses lowercase characters.

        Values of this type must be well-formed language tags,
        in conformance with the definition of well-formed tags
        in BCP 47. Implementations MAY further limit the values
        they accept to those permitted by a 'validating'
        processor, as defined in BCP 47.

        The canonical representation of values of this type is
        aligned with the SMIv2 LangTag textual convention for
        language tags fitting the length constraints imposed
        by the LangTag textual convention.";
    reference
       "RFC 5646: Tags for Identifying Languages
        RFC 5131: A MIB Textual Convention for Language Tags";
  }

  /*** collection of YANG specific types ***/

  typedef yang-identifier {
    type string {
      length "1..max";
      pattern '[a-zA-Z_][a-zA-Z0-9\-_.]*';
    }
    description
      "A YANG identifier string as defined by the 'identifier'
       rule in Section 14 of RFC 7950. An identifier must
       start with an alphabetic character or an underscore
       followed by an arbitrary sequence of alphabetic or
       numeric characters, underscores, hyphens, or dots.

       This definition conforms to YANG 1.1 defined in RFC
       7950. An earlier version of this definition excluded
       all identifiers starting with any possible combination
       of the lowercase or uppercase character sequence 'xml',
       as required by YANG 1 defined in RFC 6020. If this type
       is used in a YANG 1 context, then this restriction still
       applies.";
    reference
      "RFC 7950: The YANG 1.1 Data Modeling Language
       RFC 6020: YANG - A Data Modeling Language for the
                 Network Configuration Protocol (NETCONF)";
  }

}

<CODE ENDS>

<CODE BEGINS> file "ietf-inet-types@2025-06-23.yang"
module ietf-inet-types {

  namespace "urn:ietf:params:xml:ns:yang:ietf-inet-types";
  prefix "inet";

  organization
   "IETF Network Modeling (NETMOD) Working Group";

  contact
   "WG Web:   <https://datatracker.ietf.org/wg/netmod/>
    WG List:  <mailto:netmod@ietf.org>

    Editor:   Juergen Schoenwaelder
              <mailto:jschoenwaelder@constructor.university>";

  description
   "This module contains a collection of generally useful derived
    YANG data types for Internet addresses and related things.

    The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
    NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
    'MAY', and 'OPTIONAL' in this document are to be interpreted as
    described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
    they appear in all capitals, as shown here.

    Copyright (c) 2025 IETF Trust and the persons identified as
    authors of the code.  All rights reserved.

    Redistribution and use in source and binary forms, with or
    without modification, is permitted pursuant to, and subject
    to the license terms contained in, the Revised BSD License
    set forth in Section 4.c of the IETF Trust's Legal Provisions
    Relating to IETF Documents
    (https://trustee.ietf.org/license-info).

    This version of this YANG module is part of RFC XXXX;
    see the RFC itself for full legal notices.";

  revision 2025-06-23 {
    description
     "This revision adds the following new data types:
      - inet:ip-address-and-prefix
      - inet:ipv4-address-and-prefix
      - inet:ipv6-address-and-prefix
      - inet:protocol-number
      - inet:upper-layer-protocol-number
      - inet:host-name
      - inet:email-address
      - inet:ip-address-link-local
      - inet:ipv4-address-link-local
      - inet:ipv6-address-link-local
      The inet:host union was changed to use inet:host-name instead
      of inet:domain-name. Several pattern statements have been
      improved.";
    reference
     "RFC XXXX: Common YANG Data Types";
  }

  revision 2013-07-15 {
    description
     "This revision adds the following new data types:
      - inet:ip-address-no-zone
      - inet:ipv4-address-no-zone
      - inet:ipv6-address-no-zone";
    reference
     "RFC 6991: Common YANG Data Types";
  }

  revision 2010-09-24 {
    description
     "Initial revision.";
    reference
     "RFC 6021: Common YANG Data Types";
  }

  /*** collection of types related to protocol fields ***/

  typedef ip-version {
    type enumeration {
      enum unknown {
        value "0";
        description
         "An unknown or unspecified version of the Internet
          protocol.";
      }
      enum ipv4 {
        value "1";
        description
         "The IPv4 protocol as defined in RFC 791.";
      }
      enum ipv6 {
        value "2";
        description
         "The IPv6 protocol as defined in RFC 8200.";
      }
    }
    description
     "This value represents the version of the IP protocol.

      In the value set and its semantics, this type is equivalent
      to the InetVersion textual convention of the SMIv2.";
    reference
     "RFC  791: Internet Protocol
      RFC 8200: Internet Protocol, Version 6 (IPv6) Specification
      RFC 4001: Textual Conventions for Internet Network Addresses";
  }

  typedef dscp {
    type uint8 {
      range "0..63";
    }
    description
     "The dscp type represents a Differentiated Services Code Point
      that may be used for marking packets in a traffic stream.

      In the value set and its semantics, this type is equivalent
      to the Dscp textual convention of the SMIv2.";
    reference
     "RFC 3289: Management Information Base for the Differentiated
                Services Architecture
      RFC 2474: Definition of the Differentiated Services Field
                (DS Field) in the IPv4 and IPv6 Headers
      RFC 2780: IANA Allocation Guidelines For Values In
                the Internet Protocol and Related Headers";
  }

  typedef ipv6-flow-label {
    type uint32 {
      range "0..1048575";
    }
    description
     "The ipv6-flow-label type represents the flow identifier or
      Flow Label in an IPv6 packet header that may be used to
      discriminate traffic flows.

      In the value set and its semantics, this type is equivalent
      to the IPv6FlowLabel textual convention of the SMIv2.";
    reference
     "RFC 3595: Textual Conventions for IPv6 Flow Label
      RFC 8200: Internet Protocol, Version 6 (IPv6) Specification";
  }

  typedef port-number {
    type uint16 {
      range "0..65535";
    }
    description
     "The port-number type represents a 16-bit port number of an
      Internet transport-layer protocol such as UDP, TCP, DCCP, or
      SCTP.

      Port numbers are assigned by IANA.  The current list of
      all assignments is available from <https://www.iana.org/>.

      Note that the port number value zero is reserved by IANA.  In
      situations where the value zero does not make sense, it can
      be excluded by subtyping the port-number type.

      In the value set and its semantics, this type is equivalent
      to the InetPortNumber textual convention of the SMIv2.";
    reference
     "RFC  768: User Datagram Protocol
      RFC 9293: Transmission Control Protocol (TCP)
      RFC 9260: Stream Control Transmission Protocol
      RFC 4340: Datagram Congestion Control Protocol (DCCP)
      RFC 4001: Textual Conventions for Internet Network Addresses";
  }

  typedef protocol-number {
    type uint8;
    description
     "The protocol-number type represents an 8-bit Internet
      protocol number, carried in the 'protocol' field of the
      IPv4 header or in the 'next header' field of the IPv6
      header.

      Protocol numbers are assigned by IANA. The current list of
      all assignments is available from <https://www.iana.org/>.";
    reference
     "RFC  791: Internet Protocol
      RFC 8200: Internet Protocol, Version 6 (IPv6) Specification";
  }

  typedef upper-layer-protocol-number {
    type protocol-number;
    description
     "The upper-layer-protocol-number represents the upper-layer
      protocol number carried in an IP packet. For IPv6 packets
      with extension headers, this is the protocol number carried
      in the last 'next header' field of the chain of IPv6 extension
      headers.";
    reference
     "RFC  791: Internet Protocol
      RFC 8200: Internet Protocol, Version 6 (IPv6) Specification";
  }

  /*** collection of types related to autonomous systems ***/

  typedef as-number {
    type uint32;
    description
     "The as-number type represents autonomous system numbers
      which identify an Autonomous System (AS).  An AS is a set
      of routers under a single technical administration, using
      an interior gateway protocol and common metrics to route
      packets within the AS, and using an exterior gateway
      protocol to route packets to other ASes.  IANA maintains
      the AS number space and has delegated large parts to the
      regional registries.

      Autonomous system numbers were originally limited to 16
      bits.  BGP extensions have enlarged the autonomous system
      number space to 32 bits.  This type therefore uses an uint32
      base type without a range restriction in order to support
      a larger autonomous system number space.

      In the value set and its semantics, this type is equivalent
      to the InetAutonomousSystemNumber textual convention of
      the SMIv2.";
    reference
     "RFC 1930: Guidelines for creation, selection, and registration
                of an Autonomous System (AS)
      RFC 4271: A Border Gateway Protocol 4 (BGP-4)
      RFC 4001: Textual Conventions for Internet Network Addresses
      RFC 6793: BGP Support for Four-Octet Autonomous System (AS)
                Number Space";
  }

  /*** collection of types related to IP addresses and hostnames ***/

  typedef ip-address {
    type union {
      type ipv4-address;
      type ipv6-address;
    }
    description
     "The ip-address type represents an IP address and is IP
      version neutral.  The format of the textual representation
      implies the IP version.  This type supports scoped addresses
      by allowing zone identifiers in the address format.";
    reference
     "RFC 4007: IPv6 Scoped Address Architecture";
  }

  typedef ipv4-address {
    type string {
      pattern
        '(([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])\.){3}'
      +  '([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])'
      + '(%.+)?';
    }
    description
      "The ipv4-address type represents an IPv4 address in
       dotted-quad notation.  The IPv4 address may include a zone
       index, separated by a % sign. If a system uses zone names
       that are not represented in UTF-8, then an implementation
       needs to use some mechanism to transform the local name
       into UTF-8. The definition of such a mechanism is outside
       the scope of this document.

       The zone index is used to disambiguate identical address
       values.  For link-local addresses, the zone index will
       typically be the interface index number or the name of an
       interface.  If the zone index is not present, the default
       zone of the device will be used.

       The canonical format for the zone index is the numerical
       format";
  }

  typedef ipv6-address {
    type string {
      pattern '((:|[0-9a-fA-F]{0,4}):)([0-9a-fA-F]{0,4}:){0,5}'
            + '((([0-9a-fA-F]{0,4}:)?(:|[0-9a-fA-F]{0,4}))|'
            + '(((25[0-5]|2[0-4][0-9]|[01]?[0-9]?[0-9])\.){3}'
            + '(25[0-5]|2[0-4][0-9]|[01]?[0-9]?[0-9])))'
            + '(%[A-Za-z0-9][A-Za-z0-9\-\._~/]*)?';
      pattern '(([^:]+:){6}(([^:]+:[^:]+)|(.*\..*)))|'
            + '((([^:]+:)*[^:]+)?::(([^:]+:)*[^:]+)?)'
            + '(%.+)?';
    }
    description
     "The ipv6-address type represents an IPv6 address in full,
      mixed, shortened, and shortened-mixed notation.  The IPv6
      address may include a zone index, separated by a % sign.
      If a system uses zone names that are not represented in
      UTF-8, then an implementation needs to use some mechanism
      to transform the local name into UTF-8. The definition of
      such a mechanism is outside the scope of this document.

      The zone index is used to disambiguate identical address
      values.  For link-local addresses, the zone index will
      typically be the interface index number or the name of an
      interface.  If the zone index is not present, the default
      zone of the device will be used.

      The canonical format of IPv6 addresses uses the textual
      representation defined in Section 4 of RFC 5952.  The
      canonical format for the zone index is the numerical
      format as described in Section 11.2 of RFC 4007.";
    reference
     "RFC 4291: IP Version 6 Addressing Architecture
      RFC 4007: IPv6 Scoped Address Architecture
      RFC 5952: A Recommendation for IPv6 Address Text
                Representation";
  }

  typedef ip-address-no-zone {
    type union {
      type ipv4-address-no-zone;
      type ipv6-address-no-zone;
    }
    description
     "The ip-address-no-zone type represents an IP address and is
      IP version neutral.  The format of the textual representation
      implies the IP version.  This type does not support scoped
      addresses since it does not allow zone identifiers in the
      address format.";
    reference
     "RFC 4007: IPv6 Scoped Address Architecture";
  }

  typedef ipv4-address-no-zone {
    type ipv4-address {
      pattern '[0-9\.]*';
    }
    description
      "An IPv4 address without a zone index.  This type, derived
       from the type ipv4-address, may be used in situations where
       the zone is known from the context and no zone index is
       needed.";
  }

  typedef ipv6-address-no-zone {
    type ipv6-address {
      pattern '[0-9a-fA-F:\.]*';
    }
    description
      "An IPv6 address without a zone index.  This type, derived
       from the type ipv6-address, may be used in situations where
       the zone is known from the context and no zone index is
       needed.";
    reference
     "RFC 4291: IP Version 6 Addressing Architecture
      RFC 4007: IPv6 Scoped Address Architecture
      RFC 5952: A Recommendation for IPv6 Address Text
                Representation";
  }

  typedef ip-address-link-local {
    type union {
      type ipv4-address-link-local;
      type ipv6-address-link-local;
    }
    description
     "The ip-address-link-local type represents a link-local IP
      address and is IP version neutral. The format of the textual
      representation implies the IP version.";
  }

  typedef ipv4-address-link-local {
    type ipv4-address {
      pattern '169\.254\..*';
    }
    description
      "A link-local IPv4 address in the prefix 169.254.0.0/16 as
       defined in section 2.1. of RFC 3927.";
    reference
      "RFC 3927: Dynamic Configuration of IPv4 Link-Local Addresses";
  }

  typedef ipv6-address-link-local {
    type ipv6-address {
      pattern '[fF][eE]80:.*';
    }
    description
      "A link-local IPv6 address in the prefix fe80::/10 as defined
       in section 2.5.6. of RFC 4291.";
    reference
      "RFC 4291: IP Version 6 Addressing Architecture";
  }

  typedef ip-prefix {
    type union {
      type ipv4-prefix;
      type ipv6-prefix;
    }
    description
     "The ip-prefix type represents an IP prefix and is IP
      version neutral.  The format of the textual representations
      implies the IP version.";
  }

  typedef ipv4-prefix {
    type string {
      pattern
         '(([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])\.){3}'
       +  '([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])'
       + '/(([0-9])|([1-2][0-9])|(3[0-2]))';
    }
    description
     "The ipv4-prefix type represents an IPv4 prefix.
      The prefix length is given by the number following the
      slash character and must be less than or equal to 32.

      A prefix length value of n corresponds to an IP address
      mask that has n contiguous 1-bits from the most
      significant bit (MSB) and all other bits set to 0.

      The canonical format of an IPv4 prefix has all bits of
      the IPv4 address set to zero that are not part of the
      IPv4 prefix.

      The definition of ipv4-prefix does not require that bits,
      which are not part of the prefix, are set to zero. However,
      implementations have to return values in canonical format,
      which requires non-prefix bits to be set to zero. This means
      that 192.0.2.1/24 must be accepted as a valid value but it
      will be converted into the canonical format 192.0.2.0/24.";
  }

  typedef ipv6-prefix {
    type string {
      pattern '((:|[0-9a-fA-F]{0,4}):)([0-9a-fA-F]{0,4}:){0,5}'
            + '((([0-9a-fA-F]{0,4}:)?(:|[0-9a-fA-F]{0,4}))|'
            + '(((25[0-5]|2[0-4][0-9]|[01]?[0-9]?[0-9])\.){3}'
            + '(25[0-5]|2[0-4][0-9]|[01]?[0-9]?[0-9])))'
            + '(/(([0-9])|([0-9]{2})|(1[0-1][0-9])|(12[0-8])))';
      pattern '(([^:]+:){6}(([^:]+:[^:]+)|(.*\..*)))|'
            + '((([^:]+:)*[^:]+)?::(([^:]+:)*[^:]+)?)'
            + '(/.+)';
    }
    description
     "The ipv6-prefix type represents an IPv6 prefix.
      The prefix length is given by the number following the
      slash character and must be less than or equal to 128.

      A prefix length value of n corresponds to an IP address
      mask that has n contiguous 1-bits from the most
      significant bit (MSB) and all other bits set to 0.

      The canonical format of an IPv6 prefix has all bits of
      the IPv6 address set to zero that are not part of the
      IPv6 prefix.  Furthermore, the IPv6 address is represented
      as defined in Section 4 of RFC 5952.

      The definition of ipv6-prefix does not require that bits,
      which are not part of the prefix, are set to zero. However,
      implementations have to return values in canonical format,
      which requires non-prefix bits to be set to zero. This means
      that 2001:db8::1/64 must be accepted as a valid value but it
      will be converted into the canonical format 2001:db8::/64.";
    reference
     "RFC 5952: A Recommendation for IPv6 Address Text
                Representation";
  }

  typedef ip-address-and-prefix {
    type union {
      type ipv4-address-and-prefix;
      type ipv6-address-and-prefix;
    }
    description
     "The ip-address-and-prefix type represents an IP address and
      prefix and is IP version neutral.  The format of the textual
      representations implies the IP version.";
  }

  typedef ipv4-address-and-prefix {
    type string {
      pattern
         '(([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])\.){3}'
       +  '([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-4][0-9]|25[0-5])'
       + '/(([0-9])|([1-2][0-9])|(3[0-2]))';
    }
    description
     "The ipv4-address-and-prefix type represents an IPv4
      address and an associated IPv4 prefix.
      The prefix length is given by the number following the
      slash character and must be less than or equal to 32.

      A prefix length value of n corresponds to an IP address
      mask that has n contiguous 1-bits from the most
      significant bit (MSB) and all other bits set to 0.";
  }

  typedef ipv6-address-and-prefix {
    type string {
      pattern '((:|[0-9a-fA-F]{0,4}):)([0-9a-fA-F]{0,4}:){0,5}'
            + '((([0-9a-fA-F]{0,4}:)?(:|[0-9a-fA-F]{0,4}))|'
            + '(((25[0-5]|2[0-4][0-9]|[01]?[0-9]?[0-9])\.){3}'
            + '(25[0-5]|2[0-4][0-9]|[01]?[0-9]?[0-9])))'
            + '(/(([0-9])|([0-9]{2})|(1[0-1][0-9])|(12[0-8])))';
      pattern '(([^:]+:){6}(([^:]+:[^:]+)|(.*\..*)))|'
            + '((([^:]+:)*[^:]+)?::(([^:]+:)*[^:]+)?)'
            + '(/.+)';
    }
    description
     "The ipv6-address-and-prefix type represents an IPv6
      address and an associated IPv6 prefix.
      The prefix length is given by the number following the
      slash character and must be less than or equal to 128.

      A prefix length value of n corresponds to an IP address
      mask that has n contiguous 1-bits from the most
      significant bit (MSB) and all other bits set to 0.

      The canonical format requires that the IPv6 address is
      represented as defined in Section 4 of RFC 5952.";
    reference
     "RFC 5952: A Recommendation for IPv6 Address Text
                Representation";
  }

  /*** collection of domain name and URI types ***/

  typedef domain-name {
    type string {
      length "1..253";
      pattern
        '((([a-zA-Z0-9_]([a-zA-Z0-9\-_]){0,61})?[a-zA-Z0-9]\.)*'
      + '([a-zA-Z0-9_]([a-zA-Z0-9\-_]){0,61})?[a-zA-Z0-9]\.?)'
      + '|\.';
    }
    description
     "The domain-name type represents a DNS domain name.  The
      name SHOULD be fully qualified whenever possible. This
      type does not support wildcards (see RFC 4592) or
      classless in-addr.arpa delegations (see RFC 2317).

      Internet domain names are only loosely specified.  Section
      3.5 of RFC 1034 recommends a syntax (modified in Section
      2.1 of RFC 1123).  The pattern above is intended to allow
      for current practice in domain name use, and some possible
      future expansion.  Note that Internet host names have a
      stricter syntax (described in RFC 952) than the DNS
      recommendations in RFCs 1034 and 1123. Schema nodes
      representing host names should use the host-name type
      instead of the domain-type.

      The encoding of DNS names in the DNS protocol is limited
      to 255 characters.  Since the encoding consists of labels
      prefixed by a length bytes and there is a trailing NULL
      byte, only 253 characters can appear in the textual dotted
      notation.

      The description clause of schema nodes using the domain-name
      type MUST describe when and how these names are resolved to
      IP addresses.  Note that the resolution of a domain-name value
      may require to query multiple DNS records (e.g., A for IPv4
      and AAAA for IPv6).  The order of the resolution process and
      which DNS record takes precedence can either be defined
      explicitly or may depend on the configuration of the
      resolver.

      Domain-name values use the US-ASCII encoding.  Their canonical
      format uses lowercase US-ASCII characters.  Internationalized
      domain names MUST be A-labels as per RFC 5890.";
    reference
     "RFC  952: DoD Internet Host Table Specification
      RFC 1034: Domain Names - Concepts and Facilities
      RFC 1123: Requirements for Internet Hosts -- Application
                and Support
      RFC 2317: Classless IN-ADDR.ARPA delegation
      RFC 2782: A DNS RR for specifying the location of services
                (DNS SRV)
      RFC 4592: The Role of Wildcards in the Domain Name System
      RFC 5890: Internationalized Domain Names in Applications
                (IDNA): Definitions and Document Framework
      RFC 9499: DNS Terminology";
  }

  typedef host-name {
    type domain-name {
      length "2..max";
      pattern '[a-zA-Z0-9\-\.]+';
    }
    description
     "The host-name type represents (fully qualified) host names.
      Host names must be at least two characters long (see RFC 952)
      and they are restricted to labels consisting of letters, digits
      and hyphens separated by dots (see RFC1123 and RFC 952).";
    reference
     "RFC  952: DoD Internet Host Table Specification
      RFC 1123: Requirements for Internet Hosts -- Application
                and Support";
  }

  typedef host {
    type union {
      type ip-address;
      type host-name;
    }
    description
     "The host type represents either an IP address or a (fully
      qualified) host name.";
  }

  typedef uri {
    type string {
      pattern '[a-z][a-z0-9+.-]*:.*';
    }
    description
     "The uri type represents a Uniform Resource Identifier
      (URI) as defined by the rule 'URI' in RFC 3986.

      Objects using the uri type MUST be in US-ASCII encoding,
      and MUST be normalized as described by RFC 3986 Sections
      6.2.1, 6.2.2.1, and 6.2.2.2.  Characters that can be
      represented without using percent-encoding are represented
      as characters (without percent-encoding), and all
      case-insensitive characters are set to lowercase except
      for hexadecimal digits within a percent-encoded triplet,
      which are normalized to uppercase as described in
      Section 6.2.2.1 of RFC 3986.

      The purpose of this normalization is to help provide
      unique URIs.  Note that this normalization is not
      sufficient to provide uniqueness.  Two URIs that are
      textually distinct after this normalization may still be
      equivalent.

      Objects using the uri type may restrict the schemes that
      they permit.  For example, 'data:' and 'urn:' schemes
      might not be appropriate.

      A zero-length URI is not a valid URI.  This can be used to
      express 'URI absent' where required.

      In the value set and its semantics, this type is equivalent
      to the Uri SMIv2 textual convention defined in RFC 5017.";
    reference
     "RFC 3986: Uniform Resource Identifier (URI): Generic Syntax
      RFC 3305: Report from the Joint W3C/IETF URI Planning Interest
                Group: Uniform Resource Identifiers (URIs), URLs,
                and Uniform Resource Names (URNs): Clarifications
                and Recommendations
      RFC 5017: MIB Textual Conventions for Uniform Resource
                Identifiers (URIs)";
  }

  typedef email-address {
    type string {
      pattern '.+@.+';
    }
    description
     "The email-address type represents an internationalized
      email address.

      The email address format is defined by the addr-spec
      ABNF rule in RFC 5322 section 3.4.1. This format has
      been extended by RFC 6532 to support internationalized
      email addresses. Implementations MUST support the
      internationalization extensions of RFC 6532. Support
      of the obsolete obs-local-part, obs-domain, and
      obs-qtext parts of RFC 5322 is not required.

      The domain part may use both A-labels and U-labels
      (see RFC 5890). The canonical format of the domain part
      uses lowercase characters and U-labels (RFC 5890) where
      applicable.";
    reference
     "RFC 5322: Internet Message Format
      RFC 5890: Internationalized Domain Names in Applications
                (IDNA): Definitions and Document Framework
      RFC 6531: SMTP Extension for Internationalized Email";
  }

}
<CODE ENDS>